Aathaworld is able to provide heavy equipment service in Malaysia, this inclusive of machinery repair, production line maintenance, factory building regardless of civil and structural (C&S) or mechanical and electrical (M&E). As a turnkey factory contractor in Malaysia, there are several machineries that need to be highlighted here in order for us cover.
Generator Sets (Diesel and Gas Genset)
Generator is key to every production plant as they provide adequate electricity for the manufacturing line to carry on, regardless Gas or Diesel generator set in Malaysia. There is always wear and tear as the genset ages; from fuel pipe, oil filter to alternator accessories. Genset equipment service provider in Malaysia usually does have standard maintenance checklist to follow inclusive of replacing of worn parts, air filter, fuel filter, control panel reading and indicator, fuel and coolant level check just like vehicle, lubricate parts, cooling system checking and load bank test on switches and generator set.
HVAC or Cooling Tower
Cooling tower or HVAC equipment set contractor in Malaysia has numerous tips for factory maintenance team to take note on when it comes to cooling tower system upkeep. The guidelines are inclusive of unusual noise acts as the first indicator of issue, further investigation of problem requires motor switches to be disconnected. Debris and dirts shall be cleaned up, water distribution, filtration, its nozzle check, bleed and evaporation rates inspection, other examination works should also be done such as belt-drive or gear-drive system, shaft or bearing alignment as well as oil quality and level. Of course, there are more analysis works can be carried out, but these works are machinery service contractor in Malaysia will recommend if internal operation maintenance team was employed there.
Boiler (Fire-tube and Water-tube)
Boiler is categorized into fire-tube and water-tube which also known as high or low pressure and steam or hot water boiler. Boiler is a kind of specialized equipment in a factory that requires specific experienced equipment contractor in Malaysia to service. Commonly, these contractors will perform investigation and rectification at areas such as water level, air vents, air flues, valves from leakage, lubrication tube and system, boiler’s room dirts, dusts and lime-scale. Boiler user is advised to have periodic check by boiler contractor in Malaysia, ordinarily once per year recommended by professional boiler experts.
Material Handling System
This part consists crane loading, conveyor system, feed-in system, storage protection, warehouse distribution as well as any in-process system for production. Although factory tends to go more towards on automation but semi-manual is still popular nowadays, while both setup requires proper caring and maintenance too. Material handling system specialist in Malaysia has classified few sub-divisions to be focused and managed with, including unit load, transfer batch and production batch. All these involves mechanical parts to work as a single mechanism, so the occurrence of spare parts wear and tear is not something irregular to be seen. Therefore, it is essential to engage professional factory contractor in Malaysia to consistently carry out examination and maintenance work for this one of the most important section among overall supply chain.
Fluid & Material Processing System
This division involves pressure vessel (tank), piping, tubing, its ancillary accessories such as flanges, bearings, valves; Route involves storage to processing of these substances are inclusive of liquid, gas, solid material where it might be high or low pressure or temperature, different acidic and alkali level, speed of transmission. These processing structure equipment, tank or piping system can be made up by steel, fibreglass, aluminium, clay, concrete or other materials. Hence, getting a quality fabricator and equipment contractor in Malaysia are important so they can provide proper pre-engineering, design, fabrication and after-sale service works.
Production Equipment System
This is the main system where different business unit in various industries having diverse kind of machineries and equipment, for example, ceramic tile manufacturing plant is having raw material heating, shaping in mould, drying, cooling, spraying with colour, craft with texture or pattern, cutting, polishing, quality checking, packaging, warehousing to distribution. Production equipment contractor Malaysia has different expertise which allows them to cater needs for wide range of industries, because the baseline of maintenance services is more or less the same.
Internal Engineering Machines
Some factories have their own steel or parts milling machine or themselves are fabrication or engineering plant, which nature of business operation is to do welding, milling, fabricating for metal products or equipment. Comparable engineering factories like these have multiplicity of products and services but the heavy equipment and machinery are more or less the same, depending whether it is robotic automation, automation, semi-automation or completely manual operation. These machines require machinery repair and maintenance contractor Malaysia too where outsourcing to them is a better option since effort and cost wise will save up a lot.