Aathaworld Sdn Bhd is your preferred industrial floor system supplier and contractor Malaysia, from repair existing to new concrete floor, covering KL Kuala Lumpur, Selangor, Klang Valley and other states in Malaysia. As a full service industrial flooring system provider and installer, we specialize in car park flooring, offices, restaurants, cafes, retail stores, shopping malls, supermarket, factories, garages, warehouses, production or manufacturing floor, industrial plants, automobile facilities, aircraft hangars, airport runaway, resorts, sports complexes, community halls, hospitals, residential, commercial, showrooms, hotels, food & beverages and laboratory. There are many areas in building or even infrastructure require proper flooring system, to ensure the durability and safety level are being maximized.
According to the industrial floor contractor Malaysia, there are some residential building requires appropriate flooring system such as the common corridor, walkway, balcony, outdoor kitchen; while high rise residential building such as apartment and condominium require the industrial flooring system including the driveway, walkway, generator-set room, piping and electrical room or more. The reason why common corridor, walkway or driveway require because these are those places where traffic happen to be most for the whole building, the dynamic impact brought to the floor varies from children or pet traffic, adult or group traffic, vehicle traffic as well as heavy automotive such as trucks from and to the loading bay. Commercial building and infrastructure such as hypermarket, aviation, military, coffee shops, clinic, recreation areas, bridge, substation, community hall and sport flooring will also apply industrial standard flooring because it offers wide range of functions such as anti-slip, chemical-resistant, easy to clean and many more features that not necessary to be used in weighty duty sites.
Industrial floor system supplier Malaysia always advise to strengthen those areas that withstand frequent dynamic weight and movement to ensure the underlayment such as concrete will not crack and consequently cause any further issues. Protective coating for these substrates offers additional shield since concrete will not directly receive the forces brought by users, these impacts will be absorbed by the top layers and spread along the whole piece of covering. Many of these materials will have high degree of elongation where the elasticity offers non-crack solution since from the perspective of physics, any surface that has some sort of plasticity permits the impact to be accommodated instead of breakthrough up to certain extent. Industrial floor contractor in Malaysia has concluded that few major factors that will cause the crack even when correct product has been specified on the floor applied, that is applying the coating too thin or too thick. Generally speaking, thinner than what the specified supposed known as under-applied, mostly happens when contractor or owner tries to save cost through lesser materials installation. Thicker than the recommended thickness will cause the drying process on the coating surface happen to be too quick, but those layers below the top coat could not dry and subsequently shrink and wrinkling after second coat are being applied.
Industrial floor system supplier in Malaysia does not encourage incompetent installer to take up their products to apply because when any problems arise, it is very hard to put on the responsibility to either party and this is where the finger-pointing happens. Especially, issues tend not to appear to the surface after some period of time where the problem tracing will become more difficult. For instance, a contractor applies one layer of coating instead of two layers just to save up the cost, the coating might not be peeled within the first three months and retention sum of the contractor has collected back; then, the crack or peeling off happen during the fourth month. Hence, industrial floor contractor Malaysia is normally an appointed well-trained brand applicator to the specific manufacturer. Some of the popular suppliers will only provide authority to certain approved applicator for their brand installation job, in order to reduce such risks.
Technically speaking, industrial flooring system has the most demands from plants and factories where the users require most. There are wide range in these parts of need, from chemical processing plant, machineries workshop, fabrication yard, food and beverage factory, pharmaceutical, power plant to many more. Industrial floor system supplier Malaysia has most of the common types that can be used in general industries or purpose, for instance, the waterproof UV-protective flooring chemical. This kind of system is highly suitable to outdoor use where floors expose to sunlight ultraviolet (UV), rainwater (which might contain acid) as well as other foreign objects. This category of chemical usually cost less and user who has lower budget like it although it might require regular maintenance to ensure the functionality can be optimized at all time.
Industrial floor contractor in Malaysia capable to apply most of the indoor type of general purpose industrial coating such as epoxy, polyurethane (PU), acrylic-based coating as well as other kind of resin flooring systems. Epoxy based flooring comprises of adhesive and coating, it also covers other composite elements which are fibreglass reinforcement and carbon fiber. PU (also known as polyurethane) will not melt even when it in touch with heat and often applied for hardwood flooring too because it is a clear durable oil-based protective coating that can have fast drying and save application interval time in between coating layers. Industrial flooring system supplier in Malaysia does able to supply acrylic-based floor chemical, it can be used in multiple areas including interior and exterior on top of wooden and concrete substrate; acrylic floor can be semi-glossy and presented in a single component which highly feasible to be applied for industrial purpose. Epoxy and PU flooring are the most common resin flooring components, although there are more resin flooring types which are hard-wearing that suit most of the heavy-duty oriented usage.