Civil and structural (C&S) engineering usually come together as a package when it is being offered as a service by a professional consultant, contractor, designer, materials supplier and of course, it does have the possibilities for the break-up due to its complexity as well as niche professionalism. Some of the defects or fundamental failures might not be because of the quality of civil works and purely are triggered by deteriorating conditions from the original standard in the element of structural by itself. Therefore, it is still good to be spotted and segregated into two parts when safety component strengthening (i.e. in here, would be the structure) is concerned. Add-on service by existing consultants in civil and structural can be provided upon ad-hoc request or usually included in the package when first appointed upon signing of the contract. It can be investigated further through an interview of standard operating procedures (SOP) conducted by a contractor or installer of a certain role to dig out what was going on that made it what it is today.
Additionally, materials suppliers are also important to be talked to, by reviewing their perspective as well as the source of products before concluding the factor since not all suppliers are direct manufacturers, while they may be just one of the distributors, stockists or middleman traders for all ranges of building materials in the beginning. Nevertheless, maintenance at consistent basic needed to be carried out too, therefore, it is not a non-challenge task to put report onto the table for which party is liable since not all instructions supposed to be will be proceeded by the building owner as well as whoever involve here from acting as reminder role, procuring the defect repair, tool to makeover, project or building care manager. Outsiders are usually being pointed with blame but it is definitely unfair to do so when no independent appointee such as consultant of civil and structural is in the picture. Potentially speaking, there are always chances to occur any sort of arguments that might make things worse in terms of dragging the repair, cost escalation, emotional-relationship turn sour and more.
Some contractors or manufacturers of these civil and structural products who have a lot of experience will have the capabilities to investigate further in order for such resolving too, depending on how their tools and equipment are beside the team of experts within their corporation. Anyhow, open conversation during pre-appointment of supplies, installation of works as well as issues that arise after service is preferable. On the other hand, we shall pay attention to certain adjacent challenges in addition to the original defects that can be observed with our own sights, such as the cracks that are causing waterproofing issues, truss connecting, overlayment and underlayment as well as many more components. Project managers from the building owner or developer side shall also be there to inspect the material consumption, workers’ compliance to the procedure sheet by the producer as well as specifications needed from the drawing. Prevention is always better than cure when unexpected unnecessitated happen in the program.
Where to Get Structural Contractor & Engineering for C&S in Malaysia
Aathaworld Sdn Bhd consult, supply and construct multiple outdoor and indoor civil, wet works, masonry works, structural, building, foundation, concrete or other materials based setup that can be used for any of your infrastructure, residential, commercial, industrial, recreation, leisure, construction site or temporary usage projects at customizable specification. As civil work contractor in Malaysia, we are able to provide you a consultancy, customized proposal and real execution works for your project covering new, repair, erection, refurbishment and renovation projects in KL Kuala Lumpur, Selangor, Klang Valley, JB Johor Bahru, Penang, Malacca (Melaka), Seremban Negeri Sembilan, Perak, Pahang, Kuantan, Kelantan, Terengganu, Perlis, Alor Setar Kedah, as well as Sabah and Sarawak for East Malaysia. Find out from us also for other nations in Southeast Asia (SEA) such as Singapore, Myanmar (Burma), Cambodia, Vietnam, Laos, Thailand, Indonesia, Philippines, Brunei, Bangladesh as well as China, Taiwan, Hong Kong, Australia and New Zealand. Civil and structural engineering, reverse design, steel, concrete, sand, aggregates, steel fibre, rebar (steel bar), other fundamental materials supply and installation in Malaysia as well as other regions. Contact us at info@aathaworld.com or call (WhatsApp) to +(60)11-7001 1003 (Monday to Friday) or +(60)11-1188 1003 (Saturday, Sunday & Public Holiday).
Photo credit: Media From Wix
