Aathaworld is your plumbing contractor Malaysia who can supply, install, service of maintenance for new and existing projects. We cover industrial plants, commercial and residential buildings as well as other types of infrastructural projects. Technically speaking, plumbing is actually referring to a system that is able to carry out fluids conveying from various application ranges. Mechanism and parts involved in the system include related apparatuses, various tanks, piping, valves, plumbing fixtures and more. Many people do not know if waste removing, water delivery, HVAC (Heating, Ventilation, Air-Conditioning) cannot be classified as plumbing works but instead, all these disciplines need plumbing service from specialists too. According to a plumbing contractor in Malaysia, the word “plumbing” derives from plumbum, a latin word called by Roman era. Plumbum has another definition as representative to other sectors, known as liquid silver in Latin. It is a malleable element that is very toxic, bluish-white metallic that works as galena. This liquid silver can be applied to radiation shields, paints, alloys, cable sheaths and accumulators. There is a key difference for piping and plumbing, whereas piping processes and convey fluids such as water, gases, chemicals that are installed internally or externally for industrial plants regardless of light or heavy sectors. Plumbing contractor Malaysia has to comprehensively handle the facility of water, drainage, wastewater, water treatment to deliver the fluids; mainly referred to as water element. Piping system comprises multiple pipes that can be formed with different lengths, directions, diameter, speed of flow, pressure, temperature that can either be controlled with valve, flap gate as well as connected by installing the accessories.
There are many piping accessories and fittings can be supplied as well as installed by specialists, ranging from valve, flange, cap, cross, expansion joint, adapter, plug, reducer, elbow, swage nipple, coupling, steam traps, reducer, tee, long radius bend, bush, union and olet. Olet is a little unique and the alternative names are known as outlet fitting or longer markable name, Branch Connection Fittings. Plumbing contractor in Malaysia says that this olet fitting functions as an inlet for a smaller pipe from a larger pipe, can be used for same size’s outlet-inlet too. Branch connection can be welded to the main pipe and always being addressed as the header size or the run. Olet can branch out to Sweepolet, Letrolet, Elbolet, Weldolet, Nipolet, Threadolet and Sockolet. Pipe connectors actually work as attachments of two or more pipes from one to another or to multiple, either to lengthen the shorter pipe or to amend the direction of the system in the plumbing. It can be also applied for reducing the supply of water, diversion and also combining the water flows to one directed point. Plumbing contractor Malaysia must be able to support multiple sizes of fittings in which they connect to achieve the designated flows of the whole system for plumbing and piping of building or plant. Industrial processing pipes can further studied with the nature of fluids, different intentional system requires distinctive materials in order to safeguard the fluid or maintain the longevity of the pipings to ensure the minimal costs for replacement, time for manpower to execute it as well as the consequential effect when such upkeep works need to be carried out for a lot industrial plants. For instance, when a wastewater treatment plant requires piping maintenance, it has to shut down progressively so that no many areas of residential will be affected when high usage is required.
Pipes can be manufactured from glass, copper, fibreglass, timber, plastic, polyvinyl chloride (PVC), ceramic, aluminium, clay, concrete and most commonly to see, the steel. Plumbing contractor in Malaysia shares that the most popular choice of materials to fabricate for drinking water supply are copper, unplasticized polyvinylchloride (uPVC), polyethylene (PE), chlorinated polyvinylchloride (CPVC), polybutylene, iron, copper and galvanized steel. Copper pipe is the most classical piping material that is being used for plumbing due to the reliability and extensive duration. This piping material can offer a very high resistance level against corrosion, while its properties made itself can withstand water that is cold or hot. There is another pipe that is very suitable to be applied as condensate drain, Polyvinyl Chloride (PVC) pipe. This PVC pipe is still the most applicable plastic material in the piping industry, according to plumbing contractor Malaysia. This pipe can be installed for the cooling coil as the dripping of the condensated water formed at the exterior will be collected in the drain pan which can be found under the coil. Condensate drain system can connect to the sanitary waste system from the drain pan outlet, while going through the system comprises lavatory waste, mop sink and floor drain. PVC has been applied in the industry for more than seventy years, almost 8 decades. The lighter in weight of this material can actually save the system cost and it is slightly more environmentally-friendly compared to other piping products. Plumbing contractor in Malaysia has confidence in PVC piping because of its undoubtable advantages, especially the durability, convenience for installation and safety level. It is also used widely in industrial air conditioning systems besides commercial and household sectors. Although there are other materials that can be applied in condensate drain piping systems, such as cast iron, steel, CPVC, ABS, PEX, copper and more; but those materials are unable to take over the effectiveness in cost compared to PVC material.
Plumbing system has actually few subsystems, while residential one consists of at least two, which is taking the wastewater out and bringing the freshwater in. Pressure is the key for a good residential plumbing system, whereas plumbing contractor Malaysia has to be fluent in this aspect. According to industry norm, the classical home’s water pressure shall be about 40 plus psi (Pound-force per square inch) when inlet is mentioned. However, nothing can be more than 60 psi for a typical house, unless there are super homes that are built differently. Regulator’s pressure shall be maintained at 50 psi while these settings are good enough for the water to go from ground to first or second floors, from one corner to another too. In terms of commercial usage, the workable pressure of the whole water supply line should be more than the residential area. For example, a 4 storey commercial building might require approximately 80 psi with the absence of a booster pump while a building with a central kitchen and dishwasher would require not more than 50 psi. Furthermore, booster pumps are very significant to certain designs based on the experience of a plumbing contractor in Malaysia. It acts as an enhancer of water flow and pressure, providing an additional boost for water pressure to a certain level that is required. It can also move storage tank’s water to the whole commercial or industrial facility.
Where to Get Plumbing Contractor in Malaysia
Aathaworld Sdn Bhd supply and install a broad range of plumbing system and accessories suited with multiple types of specification to fulfill to wide range of industries from power plant, manufacturing factory, food and beverage, high rise building, commercial facilities, landed properties and residential complex. We are happy to offer consultation to ensure that our end users are aware of the available types of plumbing materials, piping, tank, fittings, accessories and systems available in the market to reach the plumbing system that can be fitted the best to their specific and customizable requirement at lowest cost but highest efficiency. At Aathaworld, we ensure that we can supply and install superior plumbing systems. We do provide maintenance and regular services to keep your plumbing and piping system run smoothly at all time. As a plumbing system contractor, plumbing, piping and comprehensive range of system products supplier in Malaysia, we are able to provide design and install, including reverse engineering on the existing one to fit your project needs; including coverage such as KL Kuala Lumpur, Selangor, Klang Valley, JB Johor Bahru, Penang, Malacca (Melaka), Seremban Negeri Sembilan, Perak, Pahang, Kuantan, Kelantan, Terengganu, Perlis, Alor Setar Kedah, as well as Sabah and Sarawak for East Malaysia. In some circumstances, our products and service can cover new and maintenance in overseas countries especially Southeast Asia (SEA) countries such as Singapore, Myanmar (Burma), Cambodia, Vietnam, Laos, Thailand, Indonesia, Philippines, Brunei, Bangladesh as well as China, Taiwan, Hong Kong, Australia and New Zealand. Consult us for your piping, plumbing system supply and installation in Malaysia and other regions today at firstname.lastname@example.org or call (Wh