Aathaworld Sdn Bhd is able to service power plant project, from power plant renovation in term of engineering, procurement, construction (civil and structural, C&S), fabrication, commissioning and machinery maintenance (mechanical & electrical, M&E) work. There are so many types of electric power generation source but Malaysia’s fossil fuels are heavily relying on coal, fuel-oil and natural gas. However, due to the fact in which Malaysia is geographically located at a strategic location on the earth, it is also gifted with enormous amount of renewable energy resources, including hydro power plant, solar electric generated from solar (photovoltaic) cells, ocean and biomass. According to power plant specialist in Malaysia, there are also other thermal energy including petroleum, nuclear energy, geothermal energy as well as chemical energy such as fuel cells and batteries. Depending on the usage and location feasibility, Malaysia has also municipal waste and biogas as renewable energy source of electricity, especially the agricultural waste from palm oil industry.
Since Malaysia is the second largest oil palm producer in the World, therefore palm oil plantation and its processing plants are widespread throughout the whole Malaysia. We basically cover KL Kuala Lumpur, Selangor, Klang Valley, Kluang, Johor and other states of Malaysia. As a power plant contractor in Malaysia, that is why we promise to deliver best quality of power plant including palm oil processing factory renovation work and palm oil machinery service in Malaysia. Palm oil mill usually has their own mini power plant that can self-sustain from biomass and biogas, since those wastes produced during the palm oil process are excessive where they can sell to third party too; for example, empty fruit bunch (EFB) after fruits extracted from fresh fruit bunch. The reason why palm oil factory will have their own set up of electricity-generating plant because they are operating at 24 hours and 7 days a week, either fruits planted on its own or purchase it from third party’s estate.
Power plant specialist Malaysia mentions also, if the mill only gets the power required to run the factory from the local power substation or grid then the operating cost will be extremely unreasonable and not feasible to make revenue out of that. Technically speaking, oil palm processing factory requires consistent upgrading work to ensure operation efficiency is maximized. Performance elevation includes its working office renovation, the production transmission flow, the oil palm mill’s machinery and equipment maintenance. In this case, it is more on the power generation set-up, the mini power plant that is built in the palm oil processing mill. Power plant contractor Malaysia is capable to service palm oil mill too because it made up of similar equipment and flow. In the palm oil factory’s biomass power plant, it is constructed in a way where steam generated from the steam boiler is channeled to the steam turbine and subsequently converted into electricity that will be utilized by the whole mill. This is the best example in Malaysia for biomass power plant generating electricity for own mill, while rice plantation is another awesome renewable energy source that burns rice husk as its feedstock in its biomass power plant. Enquire us today as your power plant maintenance contractor in Malaysia, from structural building, civil works to mechanical and electrical maintenance, equipment repair, spare parts & components fabrication and other upgrading services.
Additionally, there are few other power plants that work very well in Malaysia as a tropical country. Tropical country that has even distribution of river and sea, mountain and waterfall, raining season and sunshine period; for instance, the hydro power plant, wind farm and solar energy. Hydro power utilizes the potential energy of stored water in a dam built at sufficient height, converting its predesigned high-speed water flow into kinetic energy and subsequently generating electricity. Hydro power plant contractor Malaysia is capable to design, fabricate, install and conduct maintenance of plant’s details including the forebay, intake structure, penstock, surge chamber, hydraulic turbine, generator, power house, draft tube and tailrace. Equipment that are being applied for low pressure systems including water wheel, bulb turbine set in the river and a reverse Archimedes screw. Substantial energy of electrical can be generated by a river’s paddle wheel and these set up can even produce hydroelectric from water falls at 10 meters or below. Power plant contractor Malaysia claims that there are several facilities in the hydropower system, these include pumped storage, diversion and impoundment. Although Malaysia is not the largest producer this renewable source of energy, but it contributes to at least approximately two thousand megawatts within West Malaysia itself. Some fact to know in regards to this renewable energy, China is the largest hydroelectricity producer and this power generating method has contributed at least 20 percent of all energy sources within China.
Some but not all of power plant contractor in Malaysia does service solar energy set up, because it is more relevant to specialized contractor. In a nutshell, solar-panel based power plant requires location weather has long hours of sunlight because its utilizes sun’s rays and convert it into electricity, through the installation of solar-power photovoltaic (PV) panels. Solar energy is clean, affordable, help to reduce electricity bill, low maintenance cost, diverse application and it can bring in revenue since Malaysia local grid will purchase it back from consumer who generates this source of energy. There are other kinds of power plant too such as biogas, coal-fired and more in which power plant contractor Malaysia might able to service. Power plant specialist is sometime focus on only specialized type, such as biomass, biogas, solar, wind farm, coal-fired or hydro. Anyhow, we are able to provide general power plant maintenance such as its turbine, boiler, conveyor system, tank, pipe, generator, furnace, spare parts, civil and structure or more. If design and engineering services are required, we can also take up as a power plant EPCC contractor in Malaysia, from engineering, procurement, construction and commissioning.
Where to Get Power Plant Contractor in Malaysia
Aathaworld Sdn Bhd can service many types of equipment and machineries, manufacture different kind of metal, steel and other custom made fabrication for power plant equipment, components, building and other custom made metal specification to ensure you have the best quality fabrication and supply in Malaysia to fit your requirement. As a power plant contractor and spare parts products supplier, metal bender and metal rolling specialist in Malaysia, we are able to provide customize specification, stainless steel, mild steel, sheet metal, precision metal fabrication, piping fabrication, bolt and nut fabrication, gear fabrication, tank fabrication, conveyor engineering, flanges fabrication, steel plate rolling, welding, turning, boring, drilling, cutting, polishing, fabrication and materials supply for your requirement or projects in KL Kuala Lumpur, Selangor, Klang Valley, Kluang, Johor, JB Johor Bahru, Penang, Malacca (Melaka), Seremban Negeri Sembilan, Perak, Pahang, Kuantan, Kelantan, Terengganu, Perlis, Alor Setar Kedah, as well as Sabah and Sarawak for East Malaysia; besides Malaysia, we are also able to be power plant contractor, metal and steel fabrication supplier (bending and rolling) for other countries in Southeast Asia (SEA) such as Singapore, Cambodia, Vietnam, Laos, Myanmar (Burma), Thailand, Indonesia, Philippines, Brunei.
Submit your power plant equipment engineering service, maintenance, new EPCC, metal and steel sourcing requirements either you are looking for a machinery contractor in KL Kuala Lumpur, Selangor or other states in Malaysia. Enquire us for your new equipment and engineering product Malaysia today, submit your enquiry to us today at info@aathaworld.com or call (whatsapp) to +(60)11-7001 1003 (Monday to Friday) or +(60)11-1188 1003 (Saturday, Sunday & Public Holiday).
Photo credit: thinkgeoenergy, nhregister, constructionweekonline, enison, news.jkn.co, pv-tech, constructionreviewonline, technologyreview
