Tile Adhesive | Waterproofing | Chemical Supplier Malaysia
Aathaworld Sdn Bhd offers complete tile adhesive solution, with different kind of areas of tile adhesive application, to all range of buildings, such as commercial, low-rise, high-rise, residential building, infrastructure and industrial plant. The area that we cover include wall, flooring as well as other construction chemicals for roofing, ceiling, bridge, tank, column, beam and many more. Tile adhesive supplier Malaysia capable to service you from specification preparation or design stage, supply, installation to rectification work. Tile adhesive is extremely important for countries such as Malaysia where we have relatively high humidity atmosphere and our raining season made up most of the days in a year. Hence, we require high quality and durable tile adhesive. The importance of tile adhesive cannot be neglected and every single building should have different kind of tiles; therefore, must get some sort of strong adhesive in order to ensure the adhesiveness is there as well as water element will not penetrate the building, affecting the structure and subsequently cause safety issue and other inconveniences to the tenants. Today, tile adhesive supplier in Malaysia is everywhere and there are so many brands in the market competing with each other yet they can still survive because of one critical obvious reason, the cake of this industry is tremendously huge.
During the design stage, most architects and engineers will specify the tile adhesive brands (most of them will include the word “equivalent”), level of specification to any designated area in the building. It is essential to treat different area of the building differently in order to prevent so called “over-specified” or even the “under-specified” issues. These two issues must be handled carefully since it is interrelated closely with safety and financial. Tile adhesive supplier Malaysia usually will advise to pay more budget on those areas that potentially will cause safety issues, i.e. the wall tile that was not properly installed due to inferior adhesive chemical will drop and damage the building users. However, developer or contractor will normally get more attention on structural component of the building such as load-bearing concrete column and concrete beam, from the admixture to the surface; they are more likely neglected this part and assumed will not cause severe issue afterward. According to tile adhesive supplier in Malaysia too, structural elements may turn up to be a serious issue if no proper waterproofing being treated initially. This is due to water penetration the inner part of concrete, steel in touch with water and subsequently corrosion process could occur. Corrosion will subsequently affect structural strength of these components, from foundation to load bearing wall as well as roof structure. It applies to the tile adhesive also since it has to do with waterproofing.
Tile adhesive supplier in Malaysia come across a lot of incidents where developer want to save cost and compromise on the tile adhesive or waterproofing chemicals specification, they see it most likely it will not cause serious issues on those structural parts of the building. The usage of waterproofing is to close up the porosity of concrete infill and surface, blocking chemical and water elements to infiltrate concrete, then indirectly and directly deteriorating the building. On the other hand, tile adhesive supplier Malaysia says that their products work on top of the surface, blocking the water from attacking the tile or substrate while acting as a bonding agent for the tile. Keeping the surface dry and avoid it being in touch with water cannot solve the problem, especially the building outer surface that prone to receive rain water. According to the tile adhesive supplier Malaysia, most of the waterproofing issue happens from the foundation. It is the building part that cannot be seen and being monitored obviously at most of the time, what happens underneath the slab cannot be observed neither being examined from time to time. For instance, the soil will always absorb water whenever possible, and will cause the foundation to be bounded with wet soil. Tile adhesive supplier in Malaysia claims that wet soil will swell and lose strength if the waterproofing job of the foundation did not carry out seriously. Furthermore, the water will slip up and cause the tiled floor to crack or uneven.
More to the point on how precaution move can be done is that, water passage in the concrete should be prevented with much attention while the hydrostatic pressure need to treated with some sort of proper resistance level. The treatment mentioned here is for both interior and exterior side of concrete system, waterproofing effort should be done too at the underneath and top side. Tile adhesive supplier Malaysia advises that there are several layers and method to apply the waterproofing, including the membrane sheet on the surface side in which it receives or may in touch with incoming water and chemical. They do also encourage to enhance the protection by putting in waterproofing solution into the concrete infill, known as admixture besides the external side of concrete.
Other Waterproofing Types
There are various kind of waterproofing component types such as liquid membrane, wall putty, plastering material, torch on membrane, sheet membrane, lining waterproofing, injection waterproofing and many more. Regardless of which kind of waterproofing material, they shared the same feature, which is resistance to moisture content and water. Tile adhesives supplier in Malaysia able to provide wide range of material types such as mastic, bitumen, varnish, paint and the application method can be varied too. Coupled with the emerging of advanced technology, most of the waterproofing nowadays will be equipped with synthetic resin which can protect substrate from moisture. One of the popular types of waterproofing that can be seen in the industry is lining waterproofing. The lining waterproofing has been categorized into 2 major categories by chemical industry expert, these are lining waterproofing and paintable one. Tile adhesives supplier Malaysia who offers the pioneer one is able to achieve cost competitive because it can cover from concrete, brick, other substances such as metal. Roofing felt is a good example that falls in this category which can be presented in sheet or roll form, although it is still possible to install extruded polystyrene (it can be glued to the bitumen mastic either by cold or hot method).
Another kind of material is known as liquid membrane, it can be applied to corner and edge such as connecting point of floor and wall as well as planter box, roof, retaining wall or balcony. Tile adhesives supplier in Malaysia suggests to use torch on membrane on the abovementioned areas too by applying it using gas torch gun, it is highly suitable to be installed on large surface that is flat, especially huge project to achieve economies of scale. There is another one known as injection waterproofing, common to be seen in hardware shop, applying it using injector to form a waterproofing barrier membrane between wall, ground, foundation, cold joint for the sake of improving its bearing capacity and get rid of leakage. Last but not least, there are also simple waterproofing materials such as wall putty, plastering where these products are durable and able to resist high level of chemical, mechanical, physical and damages brought by weather.
Where to Buy Tile Adhesives, Waterproofing and Other Chemicals in Malaysia
Aathaworld able to offer consultancy during specification, leak inspection, repair, supply and apply, refurbish for all types of residential, commercial buildings, factory, shoplot, office, infrastructure, pool, fountain, roofing, home renovation, office refurbishment as a waterproofing supplier and waterproofing contractor (applicator) in Kuala Lumpur (KL), Selangor, Klang Valley and other states in Malaysia. We are supplier for multiple waterproofing products brand such as Mapei, Sika, Forsoc, Greenseal, Bostik, Pentens, BASF and many more in Malaysia. Submit your enquiry to us today at firstname.lastname@example.org or call (whatsapp) to +(60)11-7001 1003 (Monday to Friday) or +(60)11-1188 1003 (Saturday, Sunday & Public Holiday).
As a waterproofing supplier and waterproofing contractor in Malaysia, we are able to provide supply and apply for your requirement or projects in KL Kuala Lumpur, Selangor, Klang Valley, JB Johor Bahru, Penang, Malacca (Melaka), Seremban Negeri Sembilan, Perak, Pahang, Kuantan, Kelantan, Terengganu, Perlis, Alor Setar Kedah, as well as Sabah and Sarawak for East Malaysia; we are also able to be waterproof supplier and waterproof contractor for other countries in Southeast Asia (SEA) such as Singapore, Cambodia, Vietnam, Laos, Myanmar (Burma), Thailand, Indonesia, Philippines, Brunei.
Photo credit: dunlopdiy, tolexo, roff, asuranagroup, youtube, wikihow